OgreMCP

OgreMCP

---

Tab Summary

Note: OgreMCP is currently named "Uplink". It will be renamed in the near future to "OgreMCP".

MCP = Master Control Panel. OgreMCP is used to pass commands via the uplink. To load the upload, type "Run ogre up" and a new window appears.

Note: Nearly all of these buttons are sending commands through the uplink, and will affect ALL sessions connected.

Main Buttons (Left side)

• There are 4 "Tabs". Clicking each of these changes which buttons appear.
  • General (default)
  • Zones 1
  • Other
  • Other2

• There are 6 static buttons. These never disappear, regardless of which "tab" you are on.
  • Lets go - Defaulted on when the bot loads. This is used to remove the following flags: Hold up, No move, Do not move, Camp spot, Fiegn death. You can also use a chat command of "lets go" in a tell/group/raid to activate this command. -Queued command. Happens when the bot finishes what it is doing.
  • Hold up - Turns OFF auto follow. -Forced command. This happens immediately, regardless if the bot is doing other things.
  • Pause - Presses the "pause" button on the bot.
  • Resume - Resumes the bot (counter to Pausing it).
  • Uplink - Uplink Controller New window (not yet released)
  • Profile - Input box to allow you to load a new profile. Example: Grind would load a grind profile if it exists. If it doesn't exist, does nothing.

General Tab

• Sanct - Sanctuary - Queues up the spell Sanctuary for templars (if it's ready).
• DivineR - Casts Divine Recovery if it's available (Cleric AA).
• Cls-Buff - Casts a class specific buff. These need to be hard coded in, currently the only one in the list, is Warlock's "Focus Casting".
• CmpSpot - Forces people to stay within a certain distance of a pre-designed spot. (Useful for knockbacks etc).
  • Input box #1 - Camp spot for who? - Who will be listening to this command. Default is all.
  • Input box #2 - Distance - Min distance <space> max distance.
    • Min distance - How close do you stay to this spot. Default is 2 (almost right on top of it).
    • Max distance - Only move to this distance if you are within this close to it (don't need any zone-wide running). Default is 75, which is quite far away.
• BDance - Makes you break dance.. err.. Will cast Blade Dance if it is available (Bard AA).

• Get Flag - If you are near a Flag merchant (Guild Strategist) and do NOT have a flag, they will get a flag.
• Use Flag - If you are near a Flag merchant (Guild Strategist) they will use the flag.
• Call GH - Call to Guild Hall if your call is up, and you're not already in a guild hall.
• Revive - Revive - WARNING! If there are multiple options, it does NOT choose the one you have highlighted. I haven't spent the time to determine which one it does.
• Repair - Repair your guild if you are:
  • Near a Guild Mender
  • Near a Mender
  • Near a Mender bot
  • There are a few others that are hard coded in, like the one in VP etc. If you have any other spots you want coded in let me know.
• Res - Counter to "Stop Res" below. Turns Resing on ONLY if it was turned off via Stop Res.
• Stop Res - Temporarly turns resing off. Use "Res" to re-enable.
• Assist - "Dynamic Assist" - Change assists on-the-fly. Note: Auto assist MUST be checked or this option does nothing.
  • Input box #1: Who should be assisting? Who will listen to this command.
  • Input box #2: Who do you want to assist?
  • Example usage: Input box#1: Mages, Input Box #2: Kannkor. This would make all mages assist Kannkor. I could then do: Input Box#1: Melee, Input box #2: Roknnak. All melee would be assisting Roknnak (while all casters are still assisting Kannkor).
  • NOTE putting a blank option in Input Box #2 clears this option for EVERYONE.
• WarMyth - Warlock Myth toggle.
• Test - Test used by Kannkor. You can ignore this (just runs a test file that you don't have).
• NoMove - "Do not move" - temporarily disables move into melee range, move behind, and auto follow. Use "Lets go" to clear.
• No Target - Clears your target. Useful to stop many various movements.

Zones 1 Tab

• Run X - Raid script for Kannkor.
• Exeter - When fighting Maldonous (sp?) Exeter in Palace of Ferzhul, every 20% all 6 people in the group must click the flames. This does that for you. Click once every time he goes away.
• Reset Z - Hmm.. not sure. Was a raid script that I think got removed.
• Trak HD - On-screen HUD that puts the name/distance of the closest PC and closest special to you. I use it when I kill Trak.
• Trak Off - Turns the Trak HD (HUD) off.
• Chel Orb - Doesn't work.. For trak.. I should probably fix it or remove it.

Other Tab

• Coming soon!

Other2 Tab

• Coming soon!

User notes/comments/suggestions:

---